Refer to the exhibit. How should the FastEthernet0/1 ports on the 2950 model switches that are
shown in the exhibit be configured to allow connectivity between all devices?
A -
The ports only need to be connected by a crossover cable.
IP addresses and routing for the network are configured as shown in the exhibit. The network
administrator issues the show ip eigrp neighbors command from Router1 and receives the output
shown below the topology. Which statement is true?
A -
It is normal for Router1 to show one active neighbor at a time to prevent routing loops.
B -
Routing is not completely configured on Router3.
C -
The IP addresses are not configured properly on the Router1 and Router3 interfaces.
D -
The no auto-summary command configured on the routers prevents Router1 and Router2 from forming a neighbor relationship.
3-
Refer to the exhibit. After SwitchB was added to the network, VLAN connectivity problems started
to occur. What caused this problem?
A -
The revision number of SwitchB was higher than the revision number of SwitchA.
B -
Both switches are in server mode in the same domain.
C -
SwitchA was not rebooted prior to adding SwitchB to the network.
D -
V2-mode is not enabled.
4-
Refer to the exhibit. The output that is shown is generated at a switch. Which one of these
statements is true?
A -
The bridge priority is lower than the default value for spanning tree.
B -
All designated ports are in a forwarding state.
C -
This switch must be the root bridge for all VLANs on this switch.
D -
All of the above.
5-
The Company network is shown below:
Based on the information shown above, when the Company network administrator attempts to
ping Host Company-PC2 from Host Company-PC1 and shown. What is a possible problem?
A -
The link between Company1 and Company2 is down.
B -
Interface Fa0/0 on Company2 is shutdown.
C -
The link between Company2 and Company3 is down.
D -
The default gateway on Company-PC1 is incorrect.
6-
Refer to the exhibit. The Bigtime router is unable to authenticate to the Littletime router. What is
the cause of the problem?
A -
The routers cannot be connected from interface S0/0 to interface S0/0.
B -
CHAP authentication cannot be used on a serial interface.
C -
The usernames are incorrectly configured on the two routers.
D -
The passwords do not match on the two routers.
7-
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured
between these routers to successfully route traffic between the attached networks. What will need
to be done in order to use RIP v2 in place of the static routes?
A -
Configure the no ip subnet-zero command on R1, R2, and R3.
B -
Dynamic routing protocols such as RIP v2 cannot be used across Frame Relay networks.
C -
Configure the s0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D -
Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
8-
Refer to the exhibit. A router interface is being configured for Frame Relay. However, as the
exhibit shows, the router will not accept the command to configure the LMI type. What is the
problem?
A -
The interface does not support Frame Relay connections.
B -
The interface does not have an IP address assigned to it yet.
C -
The interface requires that the no shutdown command be configured first.
D -
The interface requires that the encapsulation frame-relay command be configured first.
9-
Refer to the exhibit. Two buildings on the San Jose campus of a small company must be
connected to use Ethernet with a bandwidth of at least 100 Mbps. The company is concerned
about possible problems from voltage potential differences between the two buildings. Which
media type should be used for the connection?
A -
fiber optic cable
B -
coaxial cable
C -
STP cable
D -
UTP cable
10-
Users have been complaining that their Frame Relay connection to the corporate site is very slow.
The network administrator suspects that the link is overloaded. Based on the partial output of the
Router# show frame relay pvc command shown in the graphic, which output value indicates to the
local router that traffic sent to the corporate site is experiencing congestion?
