What can a network administrator utilize by using PPP Layer 2 encapsulation?
A -
compression
B -
authentication
C -
multilink support
D -
All of the above.
2-
Refer to the exhibit. A router boots to the prompt shown in the exhibit. What does this signify .and
how should the network administrator respond?
A -
This prompt signifies that the configuration file was not found in NVRAM. The network administrator should follow the prompts to enter a basic configuration.
B -
This prompt signifies that the configuration file was not found in flash memory. The network administrator should use TFTP to transfer a configuration file to the router.
C -
This prompt signifies that the IOS image in flash memory is invalid or corrupt. The network administrator should use TFTP to transfer an lOS image to the router.
D -
This prompt signifies that the router could not authenticate the user. The network administrator should modify the IOS mage and reboot the router.
3-
Refer to the exhibit. Given this output for SWITCH3, what should the network administrator's next
action be>
A -
Check the trunk encapsulation mode for SWITCH3's fa0/1 port.
B -
Check the trunk encapsulation mode for SWITCH1's fa0/2 port.
C -
Check the duplex mode for SWITCH3's fa0/1 port.
D -
Check the duplex mode for SWITCH1's fa0/2 port.
4-
Refer to the exhibit. Which of these statements correctly describes the state of the switch once the
boot process has been completed?
A -
As FastEthernet0/12 will be the last to come up.it will not be blocked by STP.
B -
Remote access management of this switch will not be possible without configuration change.
C -
More VLANs will need to be created for this switch.
D -
The switch will need a different IOS code in order to support VLANs and STP.
5-
Refer to the exhibit. The three Catalyst 2950 switches have been configured for VTP. Trunking is
properly configured and operational on all three switches. The show vlan command issued on
SwitchC displays only the default VLANs. Based on the output from the show vtp status
commands shown in the exhibit, why is this true?
A -
Only the default VLANs are configured on SwitchA.
B -
SwitchA does not have a VTP domain name configured.
C -
VTP pruning needs to be enabled on SwitchA.
D -
SwitchC needs to have the VTP domain name configured.
6-
How many hosts and submasks in 172.16. 0. 0/23 subnetted/27
A -
8 subnet 32hosts
B -
8 subnet 31 hosts
C -
16 subnet 30hosts
D -
16 subnet 32hosts
7-
This task requires you to use the CLI of Sw-AC3 to answer multiple-choice question below. This
does not require any configuration.
What kind of router is VLAN-R1?
A -
1720
B -
1841
C -
2611
D -
2620
8-
Which switch is the root bridge for VLAN 1?
A -
Sw-DS1
B -
Sw-AC1
C -
Sw-AC2
D -
Sw-AC3
9-
This task requires you to use the CLI of Sw-AC3 to answer multiple-choice question below. This
does not require any configuration.
From which switch did SW-AC3 receive the VLAN information?
A -
SW-DS1
B -
SW-AC1
C -
SW-AC2
D -
SW-AC3(locally)
10-
Refer to the exhibit. The network administrator has discovered that the VLAN configuration of
SwitchC is not synchronized with the rest of the switched network. Why is SwitchC not receiving
VTP updates?
A -
SwitchA supports a greater number of VLANs than does SwitchC.
B -
SwitchC has fewer existing VLANs than does SwitchA.
C -
SwitchC has a revision number higher than that being advertised.
D -
SwitchC should be operating in VTP server mode to receive VTP updates.
