Refer to the following protocols, which one can create a secure terminal connection to a remote
network device?
A -
ARP
B -
SSH
C -
Telnet
D -
wep
2-
Refer to the exhibit. A network administrator wants Switch3 to be the root bridge. What could be
done to ensure Switch3 will be the root?
A -
Configure the IP address on Switch3 to be higher than the IP addresses of Switch1 and Switch2.
B -
Configure the priority value on Switch3 to be higher than the priority values of Switch 1 and Switch2.
C -
Configure the BID on Switch3 to be lower than the BIDs of Switch1 and Switch2.
D -
Configure the MAC address on Switch3 to be higher than the Switch1 and Switch2 MAC addresses.
3-
What is the maximum data rate specified for IEEE 802.11b WLANs?
A -
10Mbps
B -
11Mbps
C -
54Mbps
D -
100Mbps
4-
How does using the service password-encryption command on a router provide additional
security?
A -
by encrypting all passwords passing through the router
B -
by encrypting passwords in the plain text configuration file
C -
by requiring entry of encrypted passwords for access to the device
D -
by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges
5-
Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency
with router B?
A -
The loopback addresses are on different subnets.
B -
Route summarization is enabled on both routers.
C -
The values of the dead timers on the routers are different.
D -
The process identifier on router A is different than the process identifier on router B.
6-
Refer to the exhibit. What statement is true of the configuration for this network?
Based on the information shown above, Which of the following correctly describe the configuration
for this network?
A -
The configuration that is shown provides inadequate outside address space for translation of the number of inside addresses that are supported.
B -
Because of the addressing on interface FastEthemet0/1, the Serial0/0 interface address will not support the NAT configuration as shown.
C -
The number 1 referred to in the ip nat inside source command references access-list number1.
D -
External Router must be configured with static routers to networks 172.16.2.0/24.
7-
Refer to the exhibit. The network is converged.After link-state advertisements are received from
Router_A, what information will Router_E contain in its routing table for the subnets 208.149.23.64
and 208.149.23.96?
A -
208.149.23.64[110/13] via 190.173.23.10,00:00:07, FastEthemet0/0 208.149.23.96[110/13] via 190.173.23.10,00:00:16, FastEthemet0/0
B -
208.149.23.64[110/1] via 190.172.23.10,00:00:07, Serial1/0 208.149.23.96[110/3] via 190.173.23.10,00:00:16, FastEthemet0/0
C -
208.149.23.64[110/13] via 190.173.23.10,00:00:07, Serial1/0 208.149.23.96[110/13] via 190.173.23.10,00:00:16, Serial1/0 208.149.23.96[110/13] via 190.173.23.10,00:00:16, FastEthemet0/0
D -
208.149.23.64[110/3] via 190.172.23.10,00:00:07, Serial1/0 208.149.23.96[110/3] via 190.173.23.10,00:00:16, Serial1/0
8-
Refer to exhibit. The company uses EIGRP as the routing protocol. What path will packets take
from a host on 192.168.10.192/26 network to a host on the LAN attached to router R1?
A -
The path of the packets will be R3 to R2 to R1.
B -
The path of the packets will be R3 to R1 to R2.
C -
The path of the packets will be both R3 to R2 to R1 AND R3 to R.
D -
The path of the packets will be R3 to R1.
9-
Refer to the exhibit. Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE
802.1Q-compliant trunk to another switch. Based on the output shown, What is the reason the
truck does not form, even though the proper cabling has been attached?
A -
VLANs have not been created yet.
B -
An IP address must be configured for the port.
C -
The port is currently configured for access mode.
D -
The correct encapsulation type has not been configured.
10-
Refer to the exhibit. Which switch provides the spanning-tree designated port role for the network
segment that services the printers?