A Cisco router is booting and has just completed the POST process. It is now ready to find and
load an IOS image. What function does the router perform next?
A -
It checks the configuration register
B -
It attempts to boot from a TFTP server
C -
It loads the first image file in flash memory
D -
It inspects the configuration file in NVRAM for boot instructions
2-
Which one approaches can be used while migrating from an ipv4 addressing scheme to an ipv6
scheme
A -
configure IPv4 tunnels between IPv6 islands
B -
use proxying and translation to translate IPV6 packets into IPV4 packets
C -
enable dual-stack routing
D -
All of the above.
3-
Which protocol provides a method of sharing VLAN configuration information between two Cisco
switches?
A -
VTP
B -
802.1Q
C -
RSTP
D -
STP
4-
DNS servers provide what service?
A -
They run a spell check on host names to ensure accurate routing
B -
They convert domain names into IP addresses.
C -
Given an IP address,they determine the name of the host that is sought
D -
They map individual hosts to their specific IP addresses
5-
Refer to the exhibit. What is the effect of the configuration that is shown?
What is the effect of the configuration that is shown?
A -
It tells the router or switch to try establish an SSH connection first and if that fail to use telnet.
B -
It configures a cisco network device to use the SSH protocol on incoming communications via the virtual terminal ports.
C -
It allows seven failed login attempts before the VTY lines are temporarily shutdown.
D -
It configures the virtual terminal lines with the password 030752180500.
6-
Which IPV6 routing protocol uses multicast group FFO2::8 to send updates?
A -
RIPng
B -
OSPFv3
C -
IS-IS for IPv6
D -
static
7-
Which of the following is true regarding the debug output shown in the graphic?
A -
This router was configured with the commands: RtrA(config)#router rip RtrA(config-router)#version 2 RtrA(config-router)#network 172.16.0.0 RtrA(config-router)#network 10.0.0.0
B -
This router was configured with the commands: RtrA(config)#router rip RtrA(config-router)#network 172.16.0.0 RtrA(config-router)#network 10.0.0.0
C -
Network 192.168.168.0 will be displayed in the routing table.
D -
This router was configured with the commands: RtrA(config)#router rip RtrA(config-router)#network 192.168.1.0 RtrA(config-router)#network 10.0.0.0 RtrA(config-router)#network 192.168.168.0
8-
The network administrator is asked to configure 113 point-to-point links. Which IP addressing
scheme best defines the address range and subnet mask that meet the requirement and waste
the fewest subnet and host addresses?
A -
10.10.0.0/18 subnetted with mask 255.255.255.252
B -
10.10.0.0/25 subnetted with mask 255.255.255.252
C -
10.10.0.0/24 subnetted with mask 255.255.255.252
D -
10.10.0.0/23 subnetted with mask 255.255.255.252
9-
In which integration method is an IPv6 packet encapsulated within an IPv4 protocol?
A -
dual-stack
B -
proxy
C -
tunneling
D -
dot1q
10-
A network administrator is configuring ACLs on a Cisco router, to allow IP access form the
192.168.146.0/24, 192.168.147.0/24, 192.168.148.0/2,. and 192.168.149.0/24 networks only.
Which one ACLs, when combined, should be used.
A -
access-list 10 permit ip 192.168.146.0 255 255.255.0
B -
access-list 10 permit ip 192.168.147.0 0.0.255 255
C -
access-list 10 permit ip 192.168.149.0 0.0.255.255.0